Home Improvement: Solve mysterious paint failures with a little detective work

February 1, 2012

By Paint Quality Institute

If your home’s exterior has been beset by paint problems, it pays to do a little detective work and determine the cause. That can help you avoid the same outcome when you paint again.

According to Debbie Zimmer, paint and color expert for the Paint Quality Institute, the clues can be found in the way your paint is failing. “The evidence is right there, you just need to know how to interpret it,” she says.

Peeling

If your exterior paint is peeling, the culprit is probably moisture. Peeling occurs when wet wood swells underneath the paint, causing the paint film to loosen, crack and ultimately, peel.

Water can reach the wood through un-caulked joints or a leaky roof. Another possibility: water being forced underneath the roofing shingles because of clogged rain gutters.

Moisture coming from inside the home can also create problems, whether from a leaky pipe or shower, or even excessive humidity caused by an improperly vented clothes dryer.

Blistering

Bubbles or blisters in your paint can eventually lead to peeling, so they can’t be ignored. This problem can usually be traced to either heat or moisture.

If your house was originally painted on a very hot day in direct sunshine, for example, blistering can result, especially if a dark-color paint was applied.

Sometimes, moisture is to blame. Excess moisture from within the home can build up behind the paint and cause blisters (this is less likely with latex paint, which is vapor permeable); rain or heavy dew can also produce blisters if the surface preparation wasn’t done properly or if a low-quality latex paint was used.

Checking

Horizontal and vertical cracks that create a checkerboard pattern in your paint is evidence that the paint has lost its elasticity.

Checking typically occurs on surfaces with several layers of oil-based paint. With age, oil-based paint gets brittle. When temperatures rise or fall dramatically, siding can expand or contract, but the inflexible paint simply cracks and checks.

Chalking

This condition occurs when a fine powder forms on the painted surface. Although light chalking is a desirable way for paint to wear over time, excessive chalking can cause the color of the paint to fade very quickly — evidence that the protective paint film is rapidly eroding.

Cases of extreme chalking can usually be traced to the use of a lower-quality, highly-pigmented paint, or use of an interior paint on an outdoor surface.

Discoloration

Often, discoloration is the result of mildew, a fungus resembling dirt that thrives in warm, moist conditions. Thick shrubbery near the home can make the problem worse by shading the siding and restricting the flow of air.

A second type of discoloration is “bleed-through,” which can occur with staining woods like cedar and redwood. Failure to apply a primer before painting can allow tannins within the wood to seep through the paint and mar its appearance.

What to do if your home experiences one of these problems? If you can determine the cause, Zimmer advises you correct any condition that may have led to the paint failure. If you’re stumped, call in a professional painter to do some sleuthing.

Then, when you repaint, do proper surface preparation (including the application of a primer when necessary), and use only top-quality coatings.

Top-quality, 100-percent acrylic latex paints have excellent adhesion and tremendous flexibility, so they help prevent blistering, peeling and other failures,” she said. “They even offer an extra measure of protection against mildew.”

As you can see, with a little detective work, you can get to the bottom of any paint problem. And by following Zimmer’s suggestions, you can help prevent mysterious paint failures from ever haunting you again!

To learn more, visit blog.paintquality.com or www.paintquality.com.

From the Feb. 1-7, 2012, issue

One Comment

  1. mike muennich

    July 19, 2012 at 7:13 am

    help. we have owned and painted our redwood sided house for 20 yrs. We have always had a paint blistering problem. Many contractors have provided “solutions”. None have worked. Our latest – RhinoShield – blistered 1/2 hour after final application. What should we do?

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>