Decisions about winter wheat and weeds

UIUC_logoBy Stephanie Henry
University of Illinois
College of Agricultural, Consumer and Environmental Sciences

URBANA – The most recent report on the condition of the Illinois winter wheat crop indicated approximately 10 percent of the crop was rated poor or very poor. Close to 90 percent was rated fair to excellent, and it appears likely that much of the wheat crop will remain intact.  However, in other instances farmers might elect to terminate poorer stands and plant corn or soybean, said a University of Illinois weed scientist.

“If the decision is made to plant corn or soybean into wheat stands where some plants remain alive, it is advisable to control any remaining wheat plants prior to planting either corn or soybean,” said Aaron Hager. “Controlling existing wheat stands may be accomplished through the use of tillage, herbicides, or a combination of these.”

If the wheat field was previously treated with a herbicide, Hager said growers should check for any applicable crop rotational intervals. “These could determine whether or not corn or soybean could be planted,” he said. “If a combination of herbicides and tillage will be used to terminate an existing stand, improved control might be achieved if the herbicide application occurs prior to the tillage operation, compared with the opposite order.”

Regardless of what herbicide is used to control wheat plants, Hager added that there should be an interval of 3 to 5 days or more between application and tillage to allow the herbicide to work within the plant.

“It is altogether possible that other weed species, such as maturing winter annuals, early summer annuals, biennials, or perennials might also be present in existing wheat fields.  If so, select a herbicide or herbicide combination that will provide broad-spectrum control of both grass and broadleaf weed species.”

Hager explained that if 2,4-D is included in the tank mix, growers should be aware of the intervals that must elapse between application and planting, especially for soybean, but also for corn with some formulations.

Several herbicides could be used to control existing wheat plants. Hager explained that glyphosate is very effective on grasses, including wheat. The label suggests using 0.56 lb ae to control overwintered wheat up to 6 inches tall, 0.77 lb ae to control wheat up to 12 inches tall, and 1.125 lb ae for wheat up to 18 inches tall.

He added that Gramoxone SL is a rapidly acting contact herbicide. “Efficacy on wheat can be improved when atrazine or metribuzin is tank mixed with Gramoxone SL.  A crop oil concentrate or nonionic surfactant should be included. Thorough spray coverage is essential for good control,” Hager said.

The labels of the ACCase-inhibiting herbicides (Poast, Assure II, Select Max, Fusilade DX, and Fusion) indicate these products are effective against volunteer wheat. “However, each product label also indicates a specific rotational interval between application and planting corn,” he said.

Poast is labeled for pre-plant applications, and must be made at least 30 days before planting corn. The labels of Select Max, Fusion, Fusilade DX, and Assure II indicate rotational intervals of 30, 60, 60, and 120 days, respectively, between application and planting corn.

“Herbicide applications to control weeds in wheat must be properly timed to provide good weed control and minimize the potential for crop injury,” Hager said. “Applications made to actively growing weeds and during periods of warm air temperatures generally provide more effective and complete weed control as compared with applications made during cold, cloudy conditions.”

Hager added that the labels of all herbicides commonly used for weed control in Illinois wheat have application restrictions based on the developmental stage of the wheat. The labels of most herbicides commonly used in Illinois indicate that applications must be made before the wheat-jointing or boot stage. Before making any herbicide application, consult the respective herbicide label for additional information, he cautioned.

“If you are considering applying a herbicide with liquid nitrogen as the carrier, be sure to consult the herbicide label prior to making this type of application. Not all herbicides allow applications with liquid nitrogen as the carrier, and those that do allow this might have specific recommendations for including/excluding other spray additives or their application rates,” Hager said.

slhenry@illinois.edu

Share this story